[Wireless Connections] In progress

It's just a bunch of pipes

Re: [Wireless Connections] In progress

Postby KazzaMozz » Sat Sep 22, 2012 12:45 am

Hi Brenton & Everyone
jbv wrote:I can tell that you are chuffed :)


yeah you could say that :lol: :lol:
And the good news is No MADWIFI anywhere to be seen.

So where am I at right now.
Well the update is here I am posting via USB wireless dongle. Oh I have tried a couple. One Realtek and the other Netgear Wireless-n
I have edited out my IPs etc as it is a public forum :) but so you can see where I'm at.
There are errors with the Atheros as I haven't set anything special for it. It works without doing anything extra so that's good.

Wireless Devices currently attached to the Toshiba

Bus 002 Device 005: ID 0bda:8198 Realtek Semiconductor Corp. RTL8187B Wireless Adapter
Bus 002 Device 003: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter
Bus 002 Device 002: ID 0846:9001 NetGear, Inc. WN111(v2) RangeMax Next Wireless [Atheros AR9170+AR9101]



l
o no wireless extensions.

eth0 no wireless extensions.

wlan3 IEEE 802.11bg ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off

wlan0 IEEE 802.11bg ESSID:"wlan-ap"
Mode:Managed Frequency:2.412 GHz Access Point:
Bit Rate=1 Mb/s Tx-Power=27 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=56/70 Signal level=-54 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

wlan2 IEEE 802.11bg ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off


eth0 Link encap:Ethernet HWaddr
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:26 Base address:0xe000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:124 errors:0 dropped:0 overruns:0 frame:0
TX packets:124 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:10436 (10.1 KiB) TX bytes:10436 (10.1 KiB)

wlan0 Link encap:Ethernet HWaddr
inet addr:XXX.XXX.X.XXX Bcast:XXX.XXX.X.XXX Mask:[color=XXX.XXX.XXX.X[/color]
inet6 addr: XXXXXXXXXXXXXX XXXXXXXXXScope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2610 errors:0 dropped:0 overruns:0 frame:0
TX packets:2401 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1613927 (1.5 MiB) TX bytes:255704 (249.7 KiB)

wlan3 Link encap:Ethernet HWaddr 00:1a:ef:00:59:23
inet addr:XXX.XXX.X.XXX Bcast:XXX.XXX.X.XXX Mask:XXX.XXX.XXX.X
inet6 addr: XXXXXXXXXX XXXXXXXXXXXX Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:254 errors:0 dropped:0 overruns:0 frame:0
TX packets:50 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:76513 (74.7 KiB) TX bytes:7740 (7.5 KiB)


Now if I can find the others I have (they could be packed) I will test those very quickly. Running out of time off on holidays tomorrow early AM. I digress and must stay on topic.
NdisWrapper not required as yet. If it is I have it ready to put into action too. This will have to wait till I get back from holidays. 8-)

My documents are in progress and while away I will do a fresh install and creation of all of this. I'm currently not using a virgin install.
My test bed is not worthy of creating it on this stick. There are things on here I use for other things and would not work well for creation of this.
As we all know starting clean is very important for creating a package like this. ;) With all the testing It's too easy to leave some rubbish behind no matter how careful we are.

One question do we want to add Blue-tooth capabilities or leave that till later ?

Cheers
Kazza
User avatar
KazzaMozz
 
Posts: 332
Joined: Tue Aug 21, 2012 9:59 pm
Location: Australia

Previous

Return to Networking



Who is online

Users browsing this forum: No registered users and 1 guest

cron